---
Overview of the Craftsman Weed Wacker 27cc
Key Features
The Craftsman Weed Wacker 27cc stands out for its combination of power, lightweight design, and user-friendly features. Some of its notable attributes include:
- 27cc two-stroke engine providing sufficient torque for various outdoor tasks
- Ergonomic design with a comfortable grip and balanced weight distribution
- Adjustable cutting head for different trimming angles
- Compatibility with various trimmer line sizes
- Easy start mechanism to reduce user fatigue
- Low-vibration operation for enhanced comfort during prolonged use
- Durable construction suitable for demanding outdoor conditions
Intended Use
This tool is ideal for:
- Trimming grass along fences, sidewalks, and garden beds
- Removing weeds from hard-to-reach areas
- Edging lawns and flower beds
- Clearing overgrown vegetation in small to medium-sized yards
---
Getting Started with Your Craftsman Weed Wacker 27cc
Unboxing and Inspection
Before starting, carefully unpack the weed wacker and verify all components are present:
- Main engine unit
- Cutting head or trimmer line spool
- Shoulder strap or harness (if included)
- Fuel mixture (if pre-mixed)
- User manual
Inspect each part for damage during shipping. If any components are missing or damaged, contact the retailer or manufacturer before proceeding.
Assembly Instructions
Most Craftsman weed wackers come partially assembled, but some setup is necessary:
1. Attach the trimmer head if not pre-installed.
2. Connect the shaft components securely, ensuring all locks and screws are tight.
3. Attach the shoulder strap or harness for better control.
4. Check the fuel tank and fill with the correct fuel mixture.
5. Adjust the handle and cutting head to your preferred positions.
Always refer to the specific model's manual for detailed assembly steps, as configurations may vary.
---
Operating the Craftsman Weed Wacker 27cc
Fuel Mixture and Preparation
The Craftsman 27cc two-stroke engine requires a specific fuel mix:
- 50:1 ratio of gasoline to two-stroke engine oil
- Use fresh, unleaded gasoline for best performance
- Mix thoroughly in a clean container before filling the tank
Starting Procedure
Follow these steps for easy startup:
1. Move the choke lever to the "Choke" position.
2. Turn the fuel valve to the "On" position.
3. Prime the carburetor (if applicable) by pressing the primer bulb 3-5 times.
4. Hold the weed wacker firmly on the ground or a stable surface.
5. Pull the starter cord smoothly until the engine fires.
6. Gradually move the choke to the "Run" position after the engine warms up.
7. Squeeze the trigger to begin trimming.
Trimming Techniques
- Keep the cutting head at a consistent height for an even cut.
- Use smooth, controlled motions to trim weeds and grass.
- Avoid applying excessive pressure; let the tool do the work.
- For edging, tilt the trimmer head at a slight angle against the surface.
---
Maintenance and Care
Regular Maintenance Tasks
To keep your Craftsman Weed Wacker 27cc operating efficiently, perform routine maintenance:
- Check and clean the air filter regularly to prevent clogging.
- Inspect the trimmer line or blade for wear and replace as needed.
- Ensure the fuel tank is clean; drain and replace old fuel periodically.
- Lubricate moving parts as recommended in the manual.
- Tighten loose screws, nuts, and bolts.
Replacing the Trimmer Line
When the line becomes too short or worn:
1. Turn off the engine and disconnect the spark plug wire.
2. Remove the spool cap or cover.
3. Wind new trimmer line (usually 0.095 to 0.105 inches in diameter) onto the spool, following the diagram.
4. Reassemble the spool and cap securely.
5. Adjust the line length as per the manufacturer's instructions.
Storing the Tool
- Clean the entire tool after use.
- Empty the fuel tank or add a fuel stabilizer if storing for extended periods.
- Store in a dry, sheltered place out of children's reach.
- Keep the spark plug clean and dry.
---
Troubleshooting Common Issues
Engine Won't Start
Possible Causes:
- Fuel mixture is incorrect or stale
- Carburetor needs cleaning
- Spark plug is faulty or dirty
- Choke not in the correct position
Solutions:
- Refill with fresh fuel mixture
- Clean or replace the spark plug
- Adjust choke settings
- Clean the carburetor or seek professional service
Engine Runs but No Power
- Check for clogged air filter or fuel filter
- Inspect for line or blade obstructions
- Ensure the spark plug is functioning properly
Trimmer Line Won't Feed
- Line may be tangled or worn out
- Adjust the line length or replace the spool
---
Safety Precautions
Operating a Craftsman Weed Wacker 27cc requires adherence to safety measures:
- Always wear eye protection, gloves, and sturdy footwear.
- Keep bystanders, especially children and pets, at a safe distance.
- Never operate in wet or stormy conditions.
- Turn off the engine and disconnect the spark plug before maintenance.
- Use the tool only for its intended purpose.
---
Conclusion
The Craftsman Weed Wacker 27cc manual provides essential guidance to ensure safe and effective operation of this powerful outdoor tool. Proper assembly, regular maintenance, and adherence to safety protocols will maximize its lifespan and performance. By understanding how to start, operate, troubleshoot, and care for your weed wacker, you can maintain a well-manicured yard with ease. Always refer to the specific manual provided with your model for detailed instructions and safety warnings, and consider professional servicing for complex repairs or engine issues. With proper care, your Craftsman 27cc weed wacker will serve as a reliable partner in maintaining your outdoor space for years to come.
Frequently Asked Questions
How do I start the Craftsman Weed Wacker 27cc manually?
To start your Craftsman 27cc weed wacker manually, first ensure the fuel tank is filled with the correct mixture, set the choke to the 'on' position, press the primer bulb several times, then pull the starter cord firmly until the engine fires. Once it starts, gradually adjust the choke to the 'run' position.
What are the maintenance steps for a Craftsman 27cc manual weed wacker?
Regular maintenance includes cleaning or replacing the air filter, checking and replacing the spark plug, ensuring the fuel mixture is fresh, inspecting the trimmer line, and cleaning the cutting head. Also, periodically inspect the carburetor and fuel lines for any leaks or blockages.
How do I replace the trimmer line on a Craftsman 27cc weed wacker manually?
To replace the line, turn off the unit and remove the spool cap. Remove the old line, cut a new length (usually around 10-15 feet), and thread it through the spool according to the manufacturer's instructions. Wind the line evenly onto the spool, leaving enough length to extend during use, then reassemble the cap.
What should I do if my Craftsman 27cc weed wacker won't start manually?
If it doesn't start, check the fuel mixture for freshness, ensure the spark plug is clean and properly connected, verify that the choke is correctly set, and inspect the air filter for clogs. Also, confirm the primer bulb is functioning and that the throttle trigger is working properly.
Is there a manual available for the Craftsman 27cc weed wacker, and where can I find it?
Yes, a manual is available for the Craftsman 27cc weed wacker. You can find it on the official Craftsman website under the 'Support' or 'Manuals' section, or contact Craftsman customer service for a digital or printed copy. Additionally, third-party websites may host downloadable PDFs of the manual.
